1243 E Broadway Rd, Tempe AZ · (480) 449-09093433 E Ft Lowell Rd, Tucson AZ · (520) 795-7970
Customer PortalSend a Case

PROCEDURE

snoring mouth guard

A snoring mouth guard fabricated without a precise fit wastes the clinician's time and the patient's trust. Dani Dental mills custom mandibular advancement devices from digital scans with a standard turnaround of 5 business days.

  • Margins verified against your prescription
  • Pre-paid two-way shipping
  • Talk to the technician who built it
  • Full digital workflow

Every snoring mouth guard case at Dani Dental runs through the lab's DSD-MAD digital workflow: digital scan acceptance, articulator-class occlusal mapping, CAD design in exocad with titration range built into the advancement arm geometry, then milling from high-density thermoplastic or hard acrylic block depending on the clinician's protocol. No hand-poured models, no wax try-in delays. The scan-to-mill pipeline removes two manual steps that account for most of the fit variance in traditionally fabricated appliances. Advancement range is specified at case intake, not retrofitted after fabrication. The referring clinician selects a starting protrusion percentage (typically 50-70 percent of maximum) and an upper advancement limit, both confirmed by the Dani technician assigned to the case before milling begins. That pre-production review is the single biggest reason fit adjustments stay at one appointment rather than three. Material selection follows a documented decision tree, not a default. Patients with bruxism concurrent with snoring receive a hard-acrylic device with a flat anterior bite plane; lighter-wear candidates receive the thermoplastic option for comfort compliance. The referring doctor chooses; the technician confirms the clinical reasoning fits the material properties. That two-way confirmation is part of the named-technician accountability model Dani runs on every case. Delivery ships with a trimmed occlusal contact map printed on the case card, so the delivering clinician sees exactly where first contact points are before the device goes into the patient's mouth. Adjustment time drops because the doctor is not diagnosing fit blind. If a device requires remake for a documented lab-side defect, turnaround on the remake is 3 business days with no additional charge.

HOW IT IS BUILT

From prescription to seated case.

01

Prescription in

Send a scan file or a model with your RX. A technician reads your intent before any design begins.

02

Design & verify

We design to your margin and occlusion, then verify the fit against your prescription before it ships.

03

Build at the bench

Milled, pressed, or hand-layered as the case calls for, finished by a named technician.

04

Back to your chair

Pre-paid shipping returns the case ready to seat, with the technician reachable if anything needs an adjustment.

This is our standard pipeline. The exact steps for snoring mouth guard are being detailed and will appear here.

MATERIALS

What goes in the mouth.

The material options for snoring mouth guard, from zirconia and lithium disilicate to hand-layered porcelain, are being written up. Ask for a Doctor Kit and a technician will talk through the right choice for your case.

CASE WORK

Judge the work on its result.

Before-and-after case work for snoring mouth guard is being photographed at the studio. The best proof is a case of your own. Send one and see the finish on your chair.

Send a case

COMMON QUESTIONS

What dentists ask about snoring mouth guard

What impression or scan format does Dani Dental accept for a snoring mouth guard case?
Digital intraoral scans in STL or PLY format are preferred and route directly into the DSD-MAD CAD pipeline. PVS impressions are also accepted; the lab pours and scans them in-house before design begins. Either path hits the same 5-business-day production clock. For existing patients, a prior scan on file can be reused if it is less than 18 months old and the occlusion has not changed.
Which mandibular advancement device designs does the lab fabricate?
Dani Dental currently fabricates three titratable MAD configurations: a dual-arch telescoping design for maximum titration range, a single-piece dorsal-fin design for patients with limited inter-arch space, and a soft-liner hybrid for comfort-priority cases. All three are available in both thermoplastic and hard-acrylic block. The assigned technician will confirm design selection based on the scan and the protrusion range specified at case intake.
How is the titration range specified and what is the standard starting advancement?
Titration range is confirmed before milling begins. The lab's default starting position is 60 percent of the patient's maximum protrusive range, measured from the scan, with an upper limit of 75 percent unless the prescribing clinician specifies otherwise. Titration increments of 0.5 mm are built into the advancement arm geometry at no additional charge. Any deviation from the default requires a note on the prescription form.
What is the turnaround time and does it change for rush cases?
Standard turnaround is 5 business days from scan acceptance. Rush turnaround of 3 business days is available for an additional fee noted on the current fee schedule. Rush cases enter the same DSD-MAD digital workflow; the timeline difference is queue priority, not a different process. Cases submitted before 10 a.m. MST are logged as received same day.
How does Dani Dental handle a device that does not fit at delivery?
If the fit issue is traceable to a lab-side error, the remake is fabricated at no charge with a 3-business-day turnaround. The lab requests a brief description of the fit discrepancy and, if available, a photo or re-scan. Fit issues caused by a change in the patient's dentition after the original scan are invoiced at the standard appliance rate. The assigned technician is the single point of contact throughout the adjustment process.
Can a general dentist refer a snoring mouth guard case without a sleep physician's diagnosis, or is documentation required?
Lab-side, Dani Dental fabricates from a dentist's prescription and does not require supporting sleep-study documentation to process the case. Regulatory and clinical compliance, including whether a formal OSA diagnosis is required before appliance delivery in a given state, is the prescribing clinician's responsibility. The lab recommends confirming local scope-of-practice rules before prescribing if the case does not include a physician referral.
Does the lab offer a same-arch adjustment if the patient's bite changes after delivery?
Minor occlusal adjustments to a delivered device are handled on a case-by-case basis. If the original scan is on file and the change is within the device's material tolerance, the lab can remill the lower tray only rather than remaking the full appliance, which reduces cost and cuts turnaround to 3 business days. Send a new scan of the lower arch with a note describing the change and the technician will confirm feasibility before the case is invoiced.
What information should be included on the prescription form for a snoring mouth guard?
The prescription form should include the patient's maximum protrusive range in millimeters if measured, the desired starting advancement percentage, material preference, device design preference if any, and any bruxism history that would affect material selection. If protrusive range has not been measured clinically, note that and the lab will calculate a conservative default from the scan geometry. Incomplete prescriptions are flagged by the assigned technician before production begins, not discovered at delivery.

REQUEST A DOCTOR KIT

Send us a snoring mouth guard case.

Request a Doctor Kit and we will mail RX pads, a shade guide, and pre-paid shipping. Run your first cases through the studio and judge the result on your own chair.

Request a Doctor KitTalk to a technician